- SPEEDIFY RASPBERRY PI ROUTER INSTALL
- SPEEDIFY RASPBERRY PI ROUTER UPGRADE
- SPEEDIFY RASPBERRY PI ROUTER CODE
I have an entire video dedicated to reviewing these two tiny router boards on my YouTube channel, but I'll provide a top-level summary and the benchmarks in this post. Look at the benchmarks further down this post to see what kind of difference that architecture shift made. Plus, with the freedom to access the Pi's x1 PCI Express lane directly, DFRobot's board attaches the second Gigabit NIC directly to the bus, instead of through a USB 3.0 controller, like Seeed Studios did.
SPEEDIFY RASPBERRY PI ROUTER UPGRADE
These boards are a huge upgrade from any typical Pi 4 model B multi-port router solution, since you not only have half the required device footprint, you also get two ports side-by-side and don't need an extra USB Gigabit network dongle hanging off a USB 3.0 port! The boards are tiny, and even with the Compute Module 4 installed, they are incredibly small-take a look at the entire assembled DFRobot unit, complete with a Raspberry Pi attached: Well, after months of delays due to part shortages, both DFRobot and Seeed Studios have come out with their 2-port Gigabit router board designs, and I was happy to receive a sample of each for testing: This is referring to raspi-config when setting up the Raspberry Pi.Since I started testing various PCI Express cards on the Raspberry Pi Compute Module 4, I've been excited to see what new kinds of custom networking devices people would come up with.
SPEEDIFY RASPBERRY PI ROUTER CODE
If in the nf file you have the country set as GB, make sure that the same country code is set in: grep country /etc/wpa_supplicant/wpa_nf For, example, you can set wlan0 to Always: /usr/share/speedify/speedify_cli adapter priority wlan0 alwaysĬheck if the Wi-Fi is blocked with the following command:Ĭheck that the country codes are matching. If you disable sharing and want to use the SHARE_INTERFACE as an Internet connection again, change it back to another priority.
When you start sharing, Speedify will automatically set the SHARE_INTERFACE to the NEVER priority, so that Speedify will ignore it and not use it as an Internet connection. You will need to restart the Speedify service for the change to take effect. To stop using the Wi-Fi for a hotspot, configure the sharing options in /etc/speedify/nf. You may want to make a backup of the file before doing so. On the Raspberry Pi, saved Wi-Fi networks will be stored in /etc/wpa_nf. If you are sure your configuration is correct but the hotspot isn't visible, try removing the previous network information and rebooting. Note: Sometimes saved Wi-Fi networks interfere with the hotspot appearing.
SPEEDIFY RASPBERRY PI ROUTER INSTALL
If you are using Ubuntu Server, it doesn't come with Network Manager installed, so you will need to install Network Manager for the sharing feature to work. On Ubuntu, Speedify uses Network Manager for sharing. Subsequent starts should be much quicker. The first time running this after enabling sharing might take a little while so that Speedify can install and configure the necessary packages. Exit the text editor (nano) by hitting ctrl+X and then run:: sudo service speedify-sharing restart Once you have configured the sharing settings, save the file (if you are using nano, hit ctrl+O and press enter to save).
Make sure you're not connected to a Wi-Fi network as a client, as this may stop the sharing from starting. You should set this to the correct country to comply with your local regulations for wireless networks.
To specify the country code Wi-Fi, set: WIFI_COUNTRY="US" Speedify will default to channel 1 for 2.4GHz or you can set the channel to 36 for 5 GHz To adjust the Wi-Fi channel: WIFI_CHANNEL="1" If your Wi-Fi adapter supports 5GHz, you can change: WIFI_MODE="5" Make sure to uncomment the following lines (remove #) To share over a Wi-Fi interface wlan0, set: ENABLE_SHARE=1īy default, Speedify will create a 2.4 GHz hotspot. You can edit the config with nano, in that case, the command would be as follows: sudo nano /etc/speedify/nf Configuring Speedify as a HotspotĬonfigure the sharing options in /etc/speedify/nf.
Speedify can be configured to share the VPN connection as a Wi-Fi hotspot that other devices can join. How can I share my Speedify connection on Linux (Ubuntu and Raspberry Pi OS) via Wi-Fi?
0 kommentar(er)
